›
Technology

Distance sensor accuracy: resolution, repeatability and linearity explained

Resolution, repeatability, linearity and accuracy are not the same thing. Learn how to read a distance sensor datasheet and which figure matters for your measuring task.
RA
Render Automation engineering team
10 Nov 2026
di-soric optical sensor
Further reading
ASTECH LDM laser distance sensors
Distance sensors for dust, heat and outdoor use: what to look for
Dimetix D-Series laser distance sensor
Distance sensor outputs: 4 to 20 mA, 0 to 10 V, IO-Link or RS485?
Laser vs ultrasonic distance sensor: which one should you choose?
Need help choosing a sensor?

Send us your application and our engineers in Pune will recommend a model.

Key facts in brief

  • Resolution is the smallest change a sensor can detect. It is not the same as accuracy.
  • Repeatability tells you how close repeated measurements of the same position are. It matters most for positioning and checking.
  • Linearity error describes how far the measured value deviates from the true value across the range.
  • Target colour, surface, temperature and response time all influence the figures you get in practice.

Datasheets for distance sensors list several numbers that sound similar: resolution, repeatability, linearity and accuracy. Mixing them up leads either to an overspecified, expensive sensor or to one that cannot do the job. This guide explains each term in plain language.

Resolution: the smallest detectable change

Resolution is the smallest change in distance that the sensor can still detect. A sensor with 0.01 mm resolution notices when the target moves by 0.01 mm. It does not tell you whether the absolute value is correct, only that a change happened.

Repeatability: the same answer every time

Repeatability shows how close the readings are when the sensor measures the same position again and again under the same conditions. For positioning, sorting and in-line checks this is often the most important figure, because you compare against a taught reference rather than an absolute value.

Linearity error: deviation across the range

Linearity error, often given as plus or minus a value or a percentage of the measuring range, describes how far the sensor reading drifts from the true distance between the start and end of the range. If you need the real distance, for example for thickness or gap measurement, linearity is the figure to check.

Accuracy: the total error

Some manufacturers give an overall accuracy that combines linearity, repeatability and temperature effects. It is the best single figure for absolute measurement, but always check the conditions it was measured under: target colour, temperature and measuring distance.

What else affects the result

  • Target surface: dark, shiny or structured surfaces reduce the signal and can increase noise.
  • Temperature: look for the temperature drift in the datasheet if your plant heats up during the day.
  • Response time and filters: averaging improves stability but slows the sensor down.
  • Mounting: vibration and angle errors add directly to the measurement.

How much accuracy do you really need?

A good rule is to choose a sensor whose repeatability is about five to ten times better than the tolerance you want to check. For level and positioning tasks with tolerances in millimetres, a robust ultrasonic or time-of-flight sensor is often enough. For micrometre tolerances you need a triangulation laser distance sensor.

Want us to check a datasheet for your tolerance? Send us the tolerance and the target. Send us your application and our engineers in Pune will recommend a model and send a quote.

Read next:

Resources

More articles

ASTECH LDM laser distance sensors
17.11.2026

Distance sensors for dust, heat and outdoor use: what to look for

Steel mills, cement plants and outdoor cranes push sensors to their limits. Protection class, temperature range, optics and mounting decide whether a
Dimetix D-Series laser distance sensor
03.11.2026

Distance sensor outputs: 4 to 20 mA, 0 to 10 V, IO-Link or RS485?

The output decides how the distance reaches your PLC. Analog signals are simple and universal, IO-Link adds diagnostics and remote setup, and
20.10.2026

Laser vs ultrasonic distance sensor: which one should you choose?

Laser sensors win on precision, range and spot size. Ultrasonic sensors win on liquids, transparent targets and dirty environments. A practical comparison
06.10.2026

How does a distance sensor work? Four measuring principles explained

Every distance sensor sends out light or sound and works out the distance from what comes back. Here is how triangulation, time-of-flight,